[Black+Black]
[Black+Stainless Steel]
[White+Stainless Steel]
-Suitable for all vehicles, boats and off-road vehicles, etc..
-The gauge has the advantages of high precision, quick location confirmation and short start up time.
- No Subscription is required, the GPS service is totally free.
-Measure and display current speed at a refresh rate of 0.25 seconds
-IP67 waterproof and dustproof grade
-24VDC Working Voltage
-Fixing dimension: 85mm diameter (3-3/8"), 70mm Depth (2-3/4”), GPS Sensor/Antenna wire is 12 feet long
-Indicating Range: digital GPS Speedometer, digital Tachometer, Hour Meter, COG/ODO, Trip Meter, Water Temp, Fuel Level, Oil Pressure, Voltmeter
-Stepper motors used for full range of stepping gauges, great feature with its less power consumption, longer life, higher precision, etc.
-With curved glass (with anti-fogging function)
|
|
|
---|---|---|
How to install it?- Cut an 85mm (3 3/8") hole in the panel and allow a clearance of 70mm (2 3/4”) behind the panel to fit the gauge. - Put the gauge in the hole. - Using M4 nut and C type bracket to seal up the gauge. - For the GPS antenna, you should securely fasten it in the flat position, black side upwards, preferably outside (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. And do not cut cable. |
How to adjust backlight?1.Power on the power supply first. 2.Press the back SET button or Multi-function button (less than 2 seconds) to change the back light color. 3.Color in sequence: Red(Default)->Green->Blue->White->Yellow->Kelly->Orange->Purple->Auto Mode. 4. When users select the AUTO MODE, the back light will be off for around two seconds, and switch automatically as above sequence per minute. |
Which gauges need to be used with sensors?- Speedometer, match GPS antenna. -Tachometer, match tacho sensor. -Water temp meter, match temp sensor. ohm signal refers to manual page 2. -Oil pressure meter, match pressure sensor. ohm signal refers to manual page 2. -Fuel level meter, match level sensor. ohm signal also refers to manual page 2. -Voltmeter, dont need match sensor. |
1. Turn on the power supply first.
2. Press and hold the mode button for 3 seconds to enter the setting speed ratio mode. then adjust speed ratio from 1-300 according to your request.
3. After setting, Data is automatically saved.
4. Please note: If your sensor is installed on the flying wheel panel, the RPM ratio is equal to the number of gears of the engine; If the speed signal takes from W-Terminal, the RPM ratio is equal to the half of the number of poles.
5. Normally, When the engine at idle state, tachometer shows 600-800rpm that means speed ratio is correct. If not, you can turn down or turn up speed ratio to check RPM difference.
Working Voltage | 18-32VDC |
Backlight | Red, Orange, Green, Yellow, Kelly, Blue, Purple, White( you can press the button to change) |
Range of Tachometer | 0-9999RPM |
Range of Speed | 0-999(km/h, MPH, knots available) |
Range of Water Temp | 40-120℃ (104-248F) |
Range of Pressure | 0-5Bar (0-72.5Psi) |
Range of Odometer | 0-999999(km miles knots available) |
Range of Hour Meter | 0-99999.9 hours |
Range of Tripmeter | 0-999.9(km/h, MPH, knots available) |
COG (Course Over Ground) | 0-359 |
Operating temperature | -30℃-75℃ |
Storage temperature | -40℃-85℃ |
Grade of protection | IP67 |
Operation mode | LCD display, stepper motor |
|
|
|
---|---|---|
How to switch speed unit?- Power on the power supply first. - Short press the back MODE button to show speed unit (Knots, MPH, Km/h). - After selecting speed unit according to your request, data is automatically saved. |
GPS Speedometer keeps counting?- After installation in the first time, GPS speedometer needs to search for signal, thats the reason that LCD counts numbers all the time. - After getting signal, LCD will come back to 0. It is normal. |
Why dont get RPM signal?Tachometer sometimes cannot get signal by ignition system. So, I suggest Tacho sensor signal. It is more stable. I suggest you can buy a Tacho sensor from Eling Parts. NO. is B07RR8NQ45, B07RN3HJ72. |
1x Multi-functional Gauge
1x GPS Speed Sensor
1x Multi-plug socket
1x Installation Instruction