Wireless setting motor steering

Are you still using a computer to change the direction of the motor?

With this flying tower, open the SpeedyBee app to instantly experience a more intuitive and cool way to change the motor mode! Tap which motor and it will start rotating at low speed, and then tap the "Modify Steering" button to complete the modification.

Product Name SpeedyBee 35A BLS Mini V2 4-in-1 ESC

• BLHeli S Firmware BLHeli SJ-H-40
• Continuous current 35A *4 ways
• Maximum current 45A *4 ways (5 seconds)
• ESC Protocol DSHOT600/300
• Input Voltage 3-6S Li-ion Battery
• Output Voltage VBAT battery voltage (for powering flight control) Am
• meter Support(Scale=250 Offset=-500) Mo
• unting holes 20x20mm φ3.6mm openings, compatible with M2/M3 screws and silicone sleeves Si
• ze 32(L)*35(W)*5.5(H)mm We
• ight 7.2g

Product Name: SpeedyBee F405 Mini 20x20 Flight Controller(1)

• Controller: STM32F405
• Gyro: CM426888
• USB Interface Type: Type-C
• Barometer: Built-in
• OSD Chip : AT7456E Chip
• Salt tooth BLE : "Supported, only for flight control and ESC reference. Please make sure that the MSP switch on UART4 is turned on
• and set the baud rate to 115200,otherwise the Bluetooth function will not work."
• WiFi :Not supported
• Wireless Firmware Update :Not support, please connect to Betaflight ground station to update the firmware.
• Wireless download & analyse black box :Not support, please connect to Betaflight ground station to analyse the black box data.
• DJl Sky Terminal Connection: Flight Control Terminal Soldering Wire Connection
• DJl Sky Terminal Compatibility : "Compatible with all DJI Sky Terminals: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the flight control.

Product Name: SpeedyBee F405 Mini 20x20 Flight Controller(2)

• The pads 9V,G,T1,R1,G,SUBS(R2) on the front right corner of the unit are connected one by one with the pads on the DJIAir Unit.
• One by one corresponding connection. Serial port 1 (T1,R1) is used for the OSD function and SUBS(R2) is used for the DJI Air Units internal
• SBUS receiver signal input"
• Black Box Storage: 8MB
• BetaFlight CC pad (Camera tuning: Support.)
• Ammeter :Support. For SpeedyBee BLS 35AV2 ESC, please set Scale=250,Offset=-500.
• Input Voltage: BS-6S Li-ion battery. The flight control is powered through the G and V wires of the 8pin connection cable or the G and V pads on the back of the flight control.
• 5V BEC output ; Group 5V output, including three +5V pads on the front of the flight control and one BZ+ pad (for buzzer). Total current load is 2A
• 9V BEC Output : Group 9V output (front 9V pads), total current load is 3A.
• 3.3V BEC Output : "Support. There is a pad named ""3V3"" on the top of the front of the flight control. This pad is designed to power a receiver with a 3.3V input.pact planes, now open the SpeedyBee App and adjust the parameter wirelessly.
• The maximum current load is 500mA."
• ESC Signal Cable : M1-M4 (Rear row or pad)
• UART Outlet : "6 groups UART1, UART2, UART3, UART4 fixed for Bluetooth MSP communication>,
• UART5 fixed for ESC telemetry , UART6".
• ESC telemetry input : R5(UART 5)

Product Name: SpeedyBee F405 Mini 20x20 Flight Controller(3)

• 2C : Supported. Located at the lower left corner of the front SDA&SCL pads. Used for connecting peripherals such as magnetometer, sonar, etc.
• BF LED pad : Supported, located at the bottom front 5V,G,LED pad. Used to connect WS2812 LED strip, controlled by BF firmware.
• Buzzer Pad : Supported. BZ+, BZ- pads to access 5V passive buzzer.
• BQOT key : Support. Press and hold the BOOT key to power on the device, it can enter the DFU mode, used to save the brick and brush the firmware
• RSSI pad ; Not supported
• Smart Port/F,Port : Not supported
• Supported Firmware Type : BetaFlight(Default Factory),INAV
• Firmware Target Name : SPEEDYBEEF405MIN
• Mounting holes: 20x20mm φ3.5mm holes, compatible with M2/M3 screws and silicone sleeves.
• Dimensions: 30(L)x 32(W)x 7.8(H)mm
• Weight: 6.3g

DII Sky Side In-Line Interface

More Features

1. The four in one electrical regulator uses the well-known and stable BB21 main control chip, and has an independent convex large solder pad for easy soldering. Using imported TDK onboard chip filtering and energy storage capacitors from Japan, providing you with a more stable and smooth flight experience. No pressure drives any of the most violent 6S motors.
2. A 4-level battery level light is placed on the side of the flight control. Plug in the battery and you will immediately see the battery level
3. Supports 8-way motors and can be used for
4. X8/Y6/fixed wing, F405V3 flight control supports 8-way motors,
5. Wireless setting motor steering,Open the SpeedyBee App to instantly experience a more intuitive and cool way to change the motor!
6. Four sets of LED light strip pads will be cool to the end, and you can switch between different lighting modes by clicking the BOOT button. You want to use BFs LED control
7. On board barometer capable of real-time sensing of aircraft altitude SD card slot supports up to 4GB black box flash memory
8. 9V2A+5V2A dual independent BEC with sufficient 4 sets of serial ports, supporting receiver+image transmission+camera+GPSUSB power supply, which can provide power to the GPS module for debugging. 22mm top bangs reserve more space for FPV cameras