Feature

●? We recommend customers start threading the hardware on by hand so as to not cross thread or strip the threads. Once secured hand tight, use the torque wrench set to the proper torque as indicated from a lug nut torque chart below. Tighten the wheel bolts/lug nuts one after the other in a criss-cross pattern.
●? Under- or over-tightening wheel-attaching hardware can be damaging and dangerous. When the lug nuts are over-torqued, this could cause stress fractures and increasing the risks of the lugs breaking under normal conditions.
●? FOR SPACERS WITH PRE-ASSEMBLED STUDS: CHECK AND RE-TORQUE ALL LUG NUTS 25-50 MILES AFTER INSTALLATION TO MANUFACTURER SPECIFICATIONS. FOR SPACERS WITHOUT PRE-ASSEMBLED STUDS: LONGER STUDS MAY BE REQUIRED FOR PROPER INSTALLATION!!!!
●? Failure to follow warnings may cause lug nuts or studs to loosen and/or break while driving, resulting in wheel loss, serious accident, injury and/or death. VIBRATIONS COULD BE A SIGN OF INCOMPATIBILITY OR IMPROPER INSTALLATION. Note: This is an aftermarket component. The trademarks used in this listing are registered trademarks of their respective owners, and are used only to identify the vehicles to which this part fits.
●? Wheels must be removed so the nuts holding the spacers to the hub can be retorqued. DO NOT INSTALL IF YOUR FACTORY WHEEL STUDS AND/OR LUG NUTS MAKE CONTACT WITH THE BACK OF YOUR WHEELS. This will prevent wheels from being properly sit & secured to the vehicle. CHECK ALL HARDWARE FOR PROPER COMPATIBILITY BEFORE INSTALLATION. DO NOT USE air tools or impact wrenches. They can cause thread stripping and over/under tightening. (Please follow the recommended torque spec listed in the fitment).


Description

Description:
Condition: New
Hub Bore Size: 66.1mm
Material: High Grade T6 Aluminum w/ Class 10.9 Carbon steel wheel studs
Spacer Type: Hub Centric
Surface Finish: Anodized Silver
Thickness: 15mm = Slightly Less Than 5/8"
Thread Type:12mm x 1.25
Vehicle Bolt Pattern: 5x4.5" (5x114.3)
Wheel Bolt Pattern: 5x4.5" (5x114.3)
Package Include: As the picture shown
Spacer Width: 15mm each side
Quantity: 2 Pieces
This spacer set includes open end lug nuts to secure the spacers onto your factory hubs

Feature:
Your Factory wheel studs may extend past the surface of the wheel spacers.  In this case you will need to:
?1) Shorten the factory studs
?2) The wheels need to have the open slots (cavities) between mounting holes.
?3) Purchase a set of shorter studs and replace them with the factory studs.
The spacers will ONLY fit on the vehicles listed below, please confirm the fitment prior purchase:
?For Infiniti:
?Ex35: 2008-2012
?Ex37: 2013
?Fx35: 2003-2012
?Fx45: 2003-2008
?Fx50: 2009-2013
?G25: 2012
?G35: 2003-2008
?G37: 2008-2013
?I30: 1996-2001
?I35: 2002-2004
?J30: 1993-1997
?Jx35: 2013
?M30: 1990-1992
?M35: 2006-2010
?M35h: 2012-2013
?M37: 2011-2013
?M45: 2001-2004, 2006-2010
?M56: 2011-2013
?Q40: 2015
?Q45: 1990-2006
?Q50: 2014-2018
?Q60: 2014-2018
?Q70: 2014-2019
?Q70L: 2015-2019
?Qx30: 2017-2018
?Qx50: 2014-2019
?Qx60: 2014-2019
?Qx70: 2014-2017
?For Nissan:
?240Sx(5 Lugs Only): 1989-1998
?350Z: 2003-2009
?370Z: 2009-2019
?Altima: 2002-2018
?GT-R: 2009-2018
?Juke: 2011-2017
?Maxima: 1989-2012, 2016-2018
?Murano: 2003-2007, 2014-2018
?Pathfinder: 2013-2018
?Quest: 1993-2002, 2004-2017
?Rouge: 2016-2018
?Rouge Sport: 2017-2018
?Sentra: 2007-2012, 2017-2018