Feature

●【 Replacing Tubes Available & Hose Storage Design 】 With the storage unit to collect oil tubes after using; without any assembling work. The sealing cap to avoid any dust or dirt and prevent the liquid from spillage during transport. The tubes can be purchased individually. Extra Ø 3.5 x 4.5mm thinnest tube for the needs of extracting oil through the small dipstick tubes and reaches the very bottom of your reservoir with no oil left.
●【 Dual-Mode & Multi-Function 】 The pneumatic mode for higher speed of oil change. Manual mode requires no other equipment to do the oil changing. One extra upgraded silicone brake bleeding hose 78.7 inches long with check valve to avoid fluid back flowing during bleeding. To switch FIRSTINFO extractor to a brake bleeder easily.
●【 Speedy Extraction 】 Equipped with 3 sizes of extra-long tubes with different diameters. Fast extraction speed of 1.8L /min. Extracts engine oil in a 4-cylinder car within few minutes in pneumatic mode and leaves no mess to clean afterward. No need to lift up or crawl under the car to drain out the oil. **Note: Gasoline, and fluid with high volatility, high corrosion, high alkalinity or acidity high temperature are FORBIDDEN to be used with this extractor.**
●【 No Limit & No Leak 】 No limit to any places; perfect for working on vehicles anytime and anywhere, and for aquarium. To extract the engine oil, brake fluid, transmission fluid and other fluid of motorcycles, vehicles, lawn mower, boat, jet ski etc.
●【 100% Genuine Guarantee 】 Please identify FIRSTINFO oil / fluid extractor that has the patent authentication. (US Patent Number: 8360741) We provide you quality assurance tools with 12+10 months after-sales warranty (10 months warranty by register) support. Help you to achieve the satisfactory shopping experience.

Description

FIRSTINFO Patented 6.5L Plus Version Pneumatic / Manual Oil Extractor Pump w/ Extra 3.5*4.5mm hose + 6.5ft Brake hose with check valve


	6.5L Manual	6.5L Manual / Pneumatic	10.5 Manual / Pneumatic	10.5L Manual	15L Manual / Pneumatic	15L Manual
Capacity	6.5 L	6.5 L	10.5 L	10.5 L	15 L	15 L
B Tube ( 7.8 x 9.8 mm, 3.28 Feet )	?	?	?	?	?	?
C Tube ( 5.3 x 6.7 mm, 3.28 Feet )	?	?	?	?	?	?
D Tube + Wire ( 4.0 x 6.0 mm, 3.28 Feet )	?	?	?	?	?	?
E Tube ( 3.5 x 4.5 mm, 3.28 Feet )	?	?	?	?	?	?
Hose Storage Unit	?	?	?	?	?	?
Dust-Proof Sealing Cap	?	?	?	?	?	?
SKU No.	A1102H	A1102USY5	A1107USY5	A1107H	A1106USY5	A1106H


	Automotive Brake Bleeding Hose	Extractor Main Hose	Extension Tube	Extension Tube	Extension Tube	Extractor Main Hose1 + Extension Tubes3 + Wire Dipstick*1
Model Number	A1106G	A1106B	A1104C	A1106D	A1104A	A1102EH4
Specification	Ø4.0 x 8.0 mm	Ø7.8 x 9.8 mm	Ø5.3 x 6.7 mm	Ø4.0 x 6.0 mm	Ø3.5 x 4.5 mm	Ø7.8 x 9.8 mm 1, Ø5.3 x 6.7 mm1, Ø4 x 6 mm1, Ø3.5 x 4.5 mm1
Length	78.7 inches (2 meters)	39.3 Inches (1 meter)	39.3 Inches (1 meter)	39.3 Inches (1 meter)	39.3 Inches (1 meter)	39.3 Inches (1 meter) each

Step 1. Install The Tubes

Connect the main hose (B: Ø 7.8 x 9.8 mm) counterclockwise with the oil extractor.
Choose an extension nylon tube hose with a suitable diameter to attach to the main hose.
Please make sure they are all connected tightly. To suck up every drop of oil down to the bottom of the reservoir.

Step 2. Insert The Tubes Into The Reservoir

Remove the oil dipstick and insert the connected tube into the dipstick pipe until it reaches the bottom of the oil pan.

Attention

Cool down the engine at least 15 minutes after driving. If the car was not used in the last 4 hours, warm it up for at least 3 minutes before extraction.

Step 3. Start To Extract Oil / Two Way Mode To Fit Any Condition

Pneumatic Operation -- Connect the extractor to air compressor and turn on the air inlet valve. The pneumatic way provides higher speed. Set the working pressure between 40-170 psi.
Manual Operation -- Close the air inlet valve and pump the handle to start extraction. The manual way requires no other equipment to work with.
Pattern designed handle provides more stability for the use.

Step 4. Pour Out The Oil

Pour out the old used fluid out to another container and take it to disposal center for recycling.

Note

There is a limit line on the tank, the fluid should not be over the limit line while pouring. If the fluid goes over the limit line, it might flow into the vacuum chamber and cause leaking.

Installation

Insert

Extraction

Pouring and Cautions

Exclusive Features


Upgraded Storage Tube The sealing cover cap allows you to transport the full unit everywhere without spillage. Storage Tube collects the oil tubes together to keep the tubes and your garage clean. Also ensures no more missing tubes.	Safety Lock The safety lock design seals the spout securely, ensuring safe operation.	Patented Products Please identify FIRSTINFO Manual/Pneumatic Oil extractor Pump-- with patent authentication. US Patent Number: 8360741	Limit Line The eagle mouth designed spout makes it fluent to pour and prevents spilling out. Do Not extract oil over the limit line on the oil extractor to prevent overflow.

Extra Functions


Brake Bleeding Hose 78.7 inches long brake bleeding hose works with most vehicles cylinder fittings. Universal rubber adapter designed to drain most standard and ABS brake systems. One-way check valve equipped on the hose to avoid backflow.	Brake Bleeding Stopper Valve Controls the speed of extraction and prevent oil in the hose from dripping after the job.	Extension Tube to Reach The Bottom of Oil Pan Suck up all drop of fluid in the bottom of it by attaching the extension tube to the main hose (B: Ø 7.8 x 9.8 mm). Make sure the tubes are all connected tightly.	Extra Thinnest Tube 3.5 x 4.5 mm Exclusive Designed for the needs of extracting oil through the small dipstick tubes. Connect with the main hose (B: Ø 7.8 x 9.8 mm). to reach bottom of your oil pan.