Feature

●?Brand New - Unused Parts
●?PP204, HA3004, 1/2" Rotor Kit, Includes Rotor, Vanes, and Insert
●?Rotor Kit 1/2" Thick Dia= 2 1/8", Desa part# PP204, GHP part#SP-KFA1000, Mi-T-M part# 68-3043, Pinnacle part# 70-022-0100
●?DESA Brands Dayton, Knipco, Koehring, Master, Reddy, Remington, Sears, TSC: Part numbers(PP204,HA3004, M22456-1)
●?PINNACLE Brands: ProTemp, Master, Remington, Heat-Stream, WorkHorse, Heat Hog & SunStream: Part numbers (70-022-0100, 700220100, 71-022-1300, 710221300)
●?GHP Brands: Dyna-Glo, Thermoheat, Dyna Glo Pro, Dyna Glo Delux: (SP-KFA1000, SPKFA1000, KFA1000)


Description

Huarntwo New Replacement PP204, HA3004 1/2" Rotor Kit for Desa, Reddy, Master Heater #70-022-0100

Huarntwo New Replacement PP204, HA3004 1/2" Rotor Kit for Desa, Reddy, Master Heater #70-022-0100Huarntwo New Replacement PP204, HA3004 1/2" Rotor Kit for Desa, Reddy, Master Heater #70-022-0100

  • Includes M22009 Insert, M224561 Pump Rotor, M8643 Pump Blade M29633 Intake Filter.
  • This is a 1/2" Rotor kit for a variety of heaters. It replaces the following part numbers : PP204 ,HA3004 ,M22456-1 ,70-022-0100 , 700220100 ,71-022-1300,710221300 ,SP-KFA1000 ,SPKFA1000 , KFA1000 ,M22456,68-3043
  • Fits Heater Models ：

1.For Reddy Heater: R30, R35, R35A, R35B, R50, R50A, R50B, R70, R70A, R70B, R70BT, R70CT, R100, R100A, R100B,R110, R150, R150A, R150AT, R150B, R150BT, R150D, R150M, R155, R165, M30, M50A, M66D, and M100D.

2.For DESA: C35, C35A, C35B, C50D, C50E, C50F, C100D, C100E, C100F, C150D, C150E, and C150F.

3.For Master: B50A, B50B, B50D, B50E, B50F, B66D, B70B, B70BT,B70D, B100A, B100B, B100D, B100G, B110, B110A,B, B150B, B150C, B150F, B150FT, B150G, B150GT, B150M, B165, B200, B200AT, B350, B600.

4.For Knipco: F30, F50A, F50E, F50F, F50G, F66D, F110D, F110E, F110F, F110G, F110H, F150F, F150G, and F150H.

5.For Remington: REM35, REM35A, REM50, REM50W, REM50A, REM50AW, REM100, REM100A, REM110, REM150, REM150A, REM150B, and REM165. 6.For Koehring: K30, K50A, K100, and K100A, PKC70ET, PKC115DT, PKC165DT，And many, many more..

  • emble the rotor is binding. disassemble unit and place fine sandpaper (600grit) on a flat surface. Sand rotor lightly motion 4 times and reassemble

  • Installation Notes：

1:Remove upper shell

2:Remove filter end cover crews using a 5/16" nut driver and remove the end cover and filters.

3:Remove pump plate screws and pum plate.

4:Remove the rotor insert and blades.

5:Clean pump housing thoroughly before installing new rotor.

6:Check the gap on rotor. Adjust to .003 to .004 if needed.

7:Assemble unit and adjust pump pressure.

  • Note : If after assemble the rotor is binding. disassemble unit and place fine sandpaper (600grit) on a flat surface. Sand rotor lightly motion 4 times and reassemble

Product information