Feature(may vary by option.)

●About program: Please choose "Generic ESP8266 Module" board in Arduino IDE to program it.
●ESP8266 ESP-01S WiFi Serial Transceiver Module with 4MB Flash Memory...upgraded from 32Mbit.Latest version esp-01s,with stronger signal.
●ESP8266 Burning Fixture Development Board compatible with ESP-01S ESP-07 ESP-07S ESP-12E ESP-12F ESP-12S ESP-F
●ESP8266 Burning Fixture all IO ports have been drawn out and can be used as ZUI small system development board or small batch burning fixture. The board supports one-click firmware download function, and add burning
●What you will get:5 X ESP8266 WiFi Serial Transceiver Module,1 X ESP8266 Burning Fixture Development Board.

[5pcs ESP8266 Module + 1pc Burning Fixture]




[5pcs ESP32-C3F + 1pc Burning Fixture]





Description

ESP-01SESP-01S

About program: Please choose "Generic ESP8266 Module" board in Arduino IDE to program it.

Description:

Comparing to esp-01, esp-01s has these advantages: The PCB layout has changed for an improvement in WiFi radio performance 4MB Flash Memory...upgraded from 32Mbit Latest version esp-01s,with stronger signal

Feature:

> SDIO 2.0, SPI, UART

> 32-pin QFN package

> Wi-Fi Direct (P2P), soft-AP

> Integrated TCP/IP protocol stack

> Integrated TR switch, balun, LNA, power amplifier and matching network

> Integrated PLLs, regulators, DCXO and power management units

> +19.5dBm output power in 802.11b mode

> Power down leakage current of <10uA

> Integrated low power 32-bit CPU could be used as application processor

> SDIO 1.1/2.0, SPI, UART

>>>

> STBC, 1×1 MIMO, 2×1 MIMO

> A-MPDU & A-MSDU aggregation & 0.4ms guard interval

> Integrated RF switch, balun, 24dBm PA, DCXO, and PMU

> Integrated RISC processor, on-chip memory and external memory interfaces

> Integrated MAC/baseband processors

> Quality of Service management

> I2S interface for high fidelity audio applications

> On-chip low-dropout linear regulators for all internal supplies

> Proprietary spurious-free clock generation architecture

> Integrated WEP, TKIP, AES, and WAPI engines

Specification:

> 802.11 b/g/n

> Wake up and transmit packets in < 2ms

> Standby power consumption of < 1.0mW (DTIM3)

Firmware DownloaderFirmware Downloader

Description:

This board is suitable for firmware burning test of modules such as ESP8266 ESP-01S/01 ESP-07/07S ESP-12E/12F/12S/F All IO ports have been exported and can be used as a minimum system development board or a small batch burning fixture. The board supports firmware one-click download function and adds programming. Mode indicator (blue light) and serial communication indicator (green light).

Notice:

The module supply voltage is 3.3V DC and the current is 500mA or more. Wi-Fi module IO maximum output current is 12mA. Wi-Fi module NRST pin is active low; EN enable pin is active high.

The Wi-Fi module enters the upgrade mode: GPIO0 is at a low level, then the module is reset and powered on; the Wi-Fi module enters the normal working mode: GPIO0 is at a high level, and the module is reset and powered.

The RXD of the Wi-Fi module is connected to the TXD of the external MCU, and the TXD of the Wi-Fi module is connected to the RXD of the external MCU.

  • Driver link
  • h*ttps://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers
ESP8266 ESP-01SESP8266 ESP-01S
ESP8266 ESP-01S WiFi Serial Transceiver 4MB Flash ModuleESP8266 ESP-01S WiFi Serial Transceiver 4MB Flash Module

Package Included:

5 X ESP8266 WiFi Serial Transceiver Module

1 X ESP8266 Burning Fixture

ESP32-S3-WROOM-1 DOIT IT ESP-32 Dupont Wire Ribbon Cables Kit Antenna NiceMCU-C3F V1.0 ESP32-WROOM-32U with WiFi Antenna
B09VB9VF1W DOIT DEVIT V1 Development Board 20cm Dupont Wire Ribbon Cables Kit DIYmall 2.4G WiFi Antenna NiceMCU-C3F V1.0 ESP32-WROOM-32U with WiFi Antenna