Feature

●Compatible with 2014-2017 for Jaguar F-Type / 2010-2017 for Jaguar XJ / 2014-2017 for Jaguar XJR / 2011-2016 for Land Rover LR4 / 2010-2016 for Land Rover Range Rover / 2010-2014 for Land Rover Range Rover Sport / 2012-2016 for Land Rover Range Rover Evoque
●Interchange Part Number: BH52-1A159-CA BH521A159CA LR066379 C2D3897 LR058024 LR031713 LR018859 C2D21601 C2D15551
●Frequency: 315MHz; Placement on Vehicle: Left, Right, Front, Rear; Package: 1 x Tire Pressure Sensor
●1-Year Limited Warranty
●IMPORTANT NOTE - Please check the description or use the year/make/model drop down bar and interchangeable part numbers to confirm the compatibility before purchasing. If you dont make sure whether this item fit your vehicles, please message us.


Description

  • BOXI has providing improved technology and outstanding performance solutions for domestic passenger cars, SUVs, trucks. BOXI offers a wide range of revolutionary products.
  • Each product is tested to perform as well as the original units and in many cases to exceed the manufactures specification.

11

  • About Tire Pressure Monitoring System Sensor
  • What is TPMS?
  • Tire Pressure Monitoring Sensor monitors tire pressure and temperature. It helps you know the situation of four tires and prompts you to take in-time actions to prevent puncture and damage to car parts caused by flat tires. It also helps prevent flat tires, forecast leakage, reduce tire wire, prolong tire life, improve fuel efficiency and increase traffic safety.

BX01800017-1BX01800017-1

Product description

  • Tire Pressure Monitoring Sensor(TPMS) Fits as below vehicles:
  • 2014-2017 Jaguar F-Type
  • 2010-2017 Jaguar XJ
  • 2014-2017 Jaguar XJR
  • 2011-2016 Land Rover LR4
  • 2010-2016 Land Rover Range Rover
  • 2010-2014 Land Rover Range Rover Sport
  • 2012-2016 Land Rover Range Rover Evoque
  • Interchange Part Number : BH52-1A159-CA BH521A159CA LR066379 C2D3897 LR058024 LR031713 LR018859 C2D21601 C2D15551
  • Color: Black
  • Frequency: 315MHz
  • Placement on Vehicle: Left, Right, Front, Rear
  • Package :1 x Tire Pressure Sensor

  • Important Notes:
  • 1.This tire pressure sensor has been programmed in advance, no need to reprogram, just trigger it with tpms scan tool.
  • 2.Please DO NOT attempt to start a sensor replacement job if your scan tool or OBD diagnostic tool cannot detect our sensor to display information such as Real ID,Pressure, Frequency, battery status
  • The TPMS sensor matching process is:
  • 1. Set the parking brake.
  • 2. Turn the ignition switch to ON/RUN with the engine off.
  • 3. Press and hold the keyless-entry fob transmitter’s LOCK and UNLOCK buttons, at the same time, for about five seconds to start the TPMS learn mode. The horn sounds twice indicating the TPMS receiver is ready and in learn mode. This can also be performed using the turn signal arm and the driver information center.
  • 4. Starting with the left-front tire, activate the sensor by holding the TPMS tool aimed upward against the tire sidewall close to the wheel rim at the valve stem location. Press and release the activate button and wait for a horn chirp.
  • 5. Once the horn chirp has sounded, the sensor information is learned and a turn signal will illuminate in the next location to be learned. On most models, the driver-side-front will be next. Once the learn mode has been enabled, each of the sensors’ unique identification codes can be learned.
  • 6. When a sensor ID has been learned, the module sends a serial data message to the BCM to sound a horn chirp. This verifies the sensor has transmitted its ID and has received and learned it. The module must learn the sensor IDs in the proper sequence to determine each sensor’s location. The first learned ID is assigned to the left-front location, the second to right-front, the third to right-rear and the fourth to left-rear.

33

The TPMS sensor matching process via DIC

  • 1.Set the parking brake.
  • 2.Turn the ignition to ON/RUN with the engine off.
  • 3.Use the MENU button to select the Vehicle Information menu in the Driver Information Center (DIC).
  • 4.Use the thumbwheel to scroll to the Tire Pressure Menu item screen.
  • 5.Press the SET/CLR button to begin the sensor matching process. A message requesting acceptance of the process should display.
  • 6.Press the SET/CLR button again to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen.

22

  • 7.Start with the driver side front tire.
  • 8.Place the relearn tool against the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.
  • 9.Repeat the procedure in Step 8 for RF/RR/LR. The horn sounds two times to indicate the sensor identification code has been matched, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.
  • 10.Turn the ignition to LOCK/OFF.

Product information