[Black+Black]
[White+Stainless]
[Black+Stainless]
-Suitable for all vehicles, boats and off-road vehicles, etc..
-The gauge has the advantages of high precision, quick location confirmation and short start up time.
- No Subscription is required, the GPS service is totally free.
-IP67 waterproof and dustproof grade
-Indicating Range: digital GPS Speedometer, digital Tachometer, Hour Meter, TRIP/ODO, Trip Meter, Water Temp, Fuel Level, Oil Pressure, Voltmeter
-Stepper motors used for full range of stepping gauges, great feature with its less power consumption, longer life, higher precision, etc.
-With curved glass (with anti-fogging function)
-Tachometer, match tacho sensor.
-Water temp meter, match temp sensor. ohm signal refers to manual page 2.
-Oil pressure meter, match pressure sensor. ohm signal refers to manual page 2.
-Fuel level meter, match level sensor. ohm signal also refers to manual page 2.
-Voltmeter, dont need match sensor.
- Cut an 85mm (3 3/8") hole in the panel and allow a clearance of 70mm (2 3/4”) behind the panel to fit the gauge.
- Put the gauge in the hole.
- Using M4 nut and C type bracket to seal up the gauge.
- For the GPS antenna, you should securely fasten it in the flat position, black side upwards, preferably outside (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Connect the antenna cable to socket in the back of the gauge. And do not cut cable.
- After installation in the first time, GPS speedometer needs to search for signal, thats the reason that LCD counts numbers all the time.
- After getting signal, LCD will come back to 0. It is normal.
- Tachometer sometimes cannot get signal by ignition system. So, I suggest Tacho sensor signal. It is more stable.
- I suggest you can buy a Tacho sensor from Eling Parts. NO. is B07RR8NQ45, B07RN3HJ72.
Fixing dimension | 85mm(3-3/8") |
Speed Range | 0~999 km/h,MPH,Knots |
Working Voltage | 12V/24V |
Trip Range | 0~999.9 km/h,MPH,Knots |
ODO Mileage Range | 0~99999.9 km,miles,knots (not adjustable) |
RPM Range | 0-9999 RPM |
Temp Range | 40-120℃/104-248℉ |
Fuel level Range | 0-100% |
Oil Pressure Range | 0-5Bar/ 0-10Bar (0-75Psi/0-150Psi) |
Hours Range | 0~99999.9 hours |
Operation mode | LCD display, stepper motor |
Protection grade | IP67 |
Other | waterproof and anti-fogging |
1. Turn on the power supply first.
2. Press and hold the mode button for 3 seconds to enter the setting speed ratio mode. then adjust speed ratio from 1-300 according to your request.
3. After setting, Data is automatically saved.
4. Please note: If your sensor is installed on the flying wheel panel, the RPM ratio is equal to the number of gears of the engine; If the speed signal takes from W-Terminal, the RPM ratio is equal to the half of the number of poles.
5. Normally, When the engine at idle state, tachometer shows 600-800rpm that means speed ratio is correct. If not, you can turn down or turn up speed ratio to check RPM difference.
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
|
---|---|---|---|---|---|---|
Multi-functional Gauge | Multi-functional Gauge | Multi-functional Gauge | Multi-functional Gauge | Multi-functional Gauge | Multi-functional Gauge | |
size | 85mm | 85mm | 85mm | 85mm | 85mm | 85mm |
color | white+stainless steel | black+stainless steel | black+black | white+stainless steel | black+stainless steel | black+stainless steel |
adjustable odometer | no | no | no | no | yes | no |
1x Multi-functional Gauge
1x GPS Speed Sensor
1x Multi-plug socket
1x Installation Instruction