Feature

●[8 BAND COVERAGE] - This mobile transceiver is designed to cover 8 bands, including 80m, 60m, 40m, 30m, 20m, 17m, 15m, and 10m. It offers a rich interface and includes CAT, PTT OUT, MIC, KEY, and a K head hand microphone.
●[HIGH EFFICIENCY] - With a transmitting efficiency of higher than 85% in 80m, 60m, 40m, 30m, and 20m bands, and higher than 80% in 17m and 15m bands, this radio transceiver ensures powerful and reliable transmissions. It also provides up to 3-5W power.
●[HIGH PERFORMANCE] - Designed with high frequency circuit design principles and excellent PCB wiring, this 8 band radio transceiver delivers outstanding performance. It features a TO 220 package pads and is built to meet professional standards.
●[FREQUENCY STABILITY] - The QRP transceiver has a separate core and RF boards to avoid signal interference. It uses a high-accuracy KDS brand TCXO with frequency accuracy better than 1PPM and frequency stability better than 0.5PPM.
●[PROFESSIONAL DESIGN] - This mobile transceiver features LPF part with genuine magnetic hold relay and LM4562 or LM833 op amp chip. It has a built-in speaker with cavity and a BNC antenna interface for enhanced convenience and functionality.


Description

Spec:

Item Type: Mobile Transceiver
Material: Aluminium Alloy
Support Full Mode: USB, LSB, CW, AM, FM (SSB Mode Has Good Reception, But Poor Transmission. AM And Fm Modes Are Free And Have Poor Results)
Filter DSP Filter: 4000, 2500, 1700, 500, 200, 100, 50hz Passband
Function DSP Function: Automatic Gain Control (AGC), Noise Reduction (NR), Xmit Voice Trigger (VOX), RX Attenuator (ATT), TX Noise Gate, TX Unit Control, Volume Control, dbm/s Meter
Sidebar, Carrier Suppression SSSSB Transmit: Better Than -45dbc, Imd3 (Dual Sound) -33dbc, Receive: Better Than -50dbc
Support Multi Band Support, Continuously Adjustable 10m/32.8ft In 80m/262.5ft Frequency Range (From 20khz 99mhz, Lossy Performance)
Open Source Firmware, Allows Experimentation, Can Add New Features, Can Share Contributions Via Github, Software Complexity: 2000 Lines Of Software Based Vovox Word Available For Fast Full Control (QSK And Semi QSK Operation) Or RX Auxiliary Switch TX In Digital Mode (No CAT Or PTT Interface Required), Using Fully Digital TX External Control Of The PTT PA Output Using Delay Stage And Software Based SSB Stage Transmitters: Control Of The Phase Of The Sill Si5351 (Via Small Frequency Changes At 800kbits/s I2c) And The Amplitude Of The PA (Via PWM PA Key Shaping Circuitry)
Three Independent Switchable Analog Front End Receiver Attenuators: (0dB, -13dB, -20dB, -33dB, -53dB, -60dB, -73dB)
Receiver Noise Floor MDS: -135 DBm At 28MHz (200Hz BW)
Receiver Front-End Selectivity: Steep -45 DB/Decade Roll Off From Tuning Frequency +/-2 KHz
Blocking Dynamic Range: 20kHz Offset 123dB, 2kHz Offset 78dB
CW Decoder, Straight Iambic A B Keyer
VFO A/B + RIT And Split, And Corresponding Relay Band Filter Switching Via I2C
CAT Support (Using for Kenwood TS 480 Protocol)
8 Band Coverage: 80m/262.5, 60m/196.9ft, 40m/131.2ft, 30m/98.4ft, 20m/65.6ft, 17m/55.8ft, 15m/49.2ft, 10m/32.8ft



Package List:
1 x Mobile